When the bottom plate is lifted, the upper limit sensor does not come on for 30 sec. When the bottom plate is lowered, the lower limit sensor does not come on for 30 sec. After lift begins, the upper limit sensor does not switch on before the pick-up solenoid switches on.
Even after the leading edge of the paper reached the fusing exit sensor, the pressure roller lift motor did not raise the pressure roller. The tray 1 lift sensor does not switch on 10 s after the tray lift motor switches on and starts lifting the bottom plate. While the polygon motor is rotating normally, no synchronizing detection signal is output for đen, leading edge for any LD other than LD0. While the polygon motor is rotating normally, no synchronizing detection signal is output for cyan, leading edgefor any LD other than LD0.
The lock signal remained HIGH for 5 sec. while the fan in the development unit was operating. When the jogger fence moves from the home position, the jogger fence HP sensor does not turn off even if the jogger motor has moved the jogger fence 153.5 mm. When the jogger fence moves to the home position, the jogger fence HP sensor does not switch on even after the jogger motor has moved the jogger fence 153.5 milimet. The machine detected an abnormal reading of the resistance of the ITB bias roller because it is near the end of its service life.
Dribbble is the world’s leading community for creatives to share, grow, and get hired. Read more about cho thue may photocopy hai phong here. The người hâm m of the lower ozone filter box not operating correctly. The fa of the middle ozone filter box not operating correctly. The người yêu thích located on the right side of the exposure unit is not rotating.
After the start of timing to create the yellow image, the PFGATE register of the GAVD did not assert. When binding pieces of paper together, you have to align them. You cho thue may photocopy hai phong use a paper guillotine to trim the edges to make sure that the sheets of paper are aligned well. Due to its versatility and precision, paper guillotines are utilized to cut from cardboards to stacks of paper.
The motor is trying to rotate at power on or during normal operation but there is an excessive load on the drum shaft. The PLL lock signal remained HIGH or LOW for longer than the prescribed time for the K, M, C, or Y, development motor. After the M, C, or Y drum started to rotate, the feedback for the charge unit of the color dropped below 0.3V.
The lift sensor is not activated within 10 seconds after the tray lift motor starts lifting the bottom plate. When the tray lowers, the tray lift sensor does not go off within 1.5 sec. The lower limit sensor of the tandem tray does not detect the lower limit within 10 sec.
Even after the leading edge of the paper reached the fusing exit sensor, the pressure roller lift motor did not raise the pressure roller. The tray 1 lift sensor does not switch on 10 s after the tray lift motor switches on and starts lifting the bottom plate. While the polygon motor is rotating normally, no synchronizing detection signal is output for đen, leading edge for any LD other than LD0. While the polygon motor is rotating normally, no synchronizing detection signal is output for cyan, leading edgefor any LD other than LD0.
The lock signal remained HIGH for 5 sec. while the fan in the development unit was operating. When the jogger fence moves from the home position, the jogger fence HP sensor does not turn off even if the jogger motor has moved the jogger fence 153.5 mm. When the jogger fence moves to the home position, the jogger fence HP sensor does not switch on even after the jogger motor has moved the jogger fence 153.5 milimet. The machine detected an abnormal reading of the resistance of the ITB bias roller because it is near the end of its service life.
Dribbble is the world’s leading community for creatives to share, grow, and get hired. Read more about cho thue may photocopy hai phong here. The người hâm m of the lower ozone filter box not operating correctly. The fa of the middle ozone filter box not operating correctly. The người yêu thích located on the right side of the exposure unit is not rotating.
After the start of timing to create the yellow image, the PFGATE register of the GAVD did not assert. When binding pieces of paper together, you have to align them. You cho thue may photocopy hai phong use a paper guillotine to trim the edges to make sure that the sheets of paper are aligned well. Due to its versatility and precision, paper guillotines are utilized to cut from cardboards to stacks of paper.
The motor is trying to rotate at power on or during normal operation but there is an excessive load on the drum shaft. The PLL lock signal remained HIGH or LOW for longer than the prescribed time for the K, M, C, or Y, development motor. After the M, C, or Y drum started to rotate, the feedback for the charge unit of the color dropped below 0.3V.
The lift sensor is not activated within 10 seconds after the tray lift motor starts lifting the bottom plate. When the tray lowers, the tray lift sensor does not go off within 1.5 sec. The lower limit sensor of the tandem tray does not detect the lower limit within 10 sec.